 |
|||||||
|
|||||||
|
|
|||||||
|
|||||||
|
|
| TW2835资料 | |
|
TW2835 PDF Download |
|
File Size : 116 KB
Manufacturer:Techwell Description:READ: The AT49BV/LV002(N)(T) is accessed like an EPROM. When CE and OE are low and WE is high, the data stored at the memory location determined by the address pins is asserted on the outputs. The outputs are put in the high impedance state whenever CE or OE is high. This dual-line control gives designers flexibility in pre- venting bus contention. COMMAND SEQUENCES: When the device is first pow- ered on it will be reset to the read or standby mode depending upon the state of the control line inputs. In order to perform other device functions, a series of command sequences are entered into the device. The command sequences are shown in the Command Definitions table. The command sequences are written by applying a low pulse on the WE or CE input with CE or WE low (respec- tively) and OE high. The address is latched on the falling edge of CE or WE, whichever occurs last. The data is latched by the first rising edge of CE or WE. Standard microprocessor write timings are used. The address loca- tions used in the command sequences are not affected by entering the command sequences. RESET: A RESET input pin is provided to ease some sys- tem applications. When RESET is at a logic high level, the device is in its standard operating mode. A low level on the RESET input halts the present device operation and puts the outputs of the device in a high impedance state. If the RESET pin makes a high to low transition during a program or erase operation, the operation may not be sucessfully completed and the operation will have to be repeated after a high level is applied to the RESET pin. When a high level is reasserted on the RESET pin, the device returns to the read or standby mode, depending upon the state of the control inputs. By applying a 12V 0.5V input signal to the RESET pin, the boot block array can be reprogrammed even if the boot block lockout feature has been enabled (see Boot Block Programming Lockout Override section). The RESET feature is not available on the AT49BV/LV002N(T). ERASURE: Before a byte can be reprogrammed, the main memory block or parameter block which contains the byte must be erased. The erased state of the memory bits is a logical 1. The entire device can be erased at one time by using a 6-byte software code. The software chip erase code consists of 6-byte load commands to specific address locations with a specific data pattern (please refer to the Chip Erase Cycle Waveforms). After the software chip erase has been initiated, the device will internally time the erase operation so that no external clocks are required. The maximum time needed to erase the whole chip is tEC. If the boot block lockout feature has been enabled, the data in the boot sector will not be erased. |
|
| 相关型号 | |
| ◆ ADP3335ARMZ-5 | |
| ◆ LTC4414EMS8 | |
| ◆ LTC1968CMS8 | |
| ◆ LTC1871EMS | |
| ◆ LTC3548AEMSE | |
| ◆ LTC1412CG/IG | |
| ◆ LTC1562IG | |
| ◆ LTC1562CG | |
| ◆ AD7705BRZ | |
| ◆ ADM3053BRWZ | |
| 1PCS | 100PCS | 1K | 10K | ||
| 价 格 | |||||
|
型 号：TW2835 厂 家：Techwell 封 装：QFP208 批 号：07+ 数 量：3510 说 明：绝对原装正品现货 |
|||||
|
运 费： 所在地：深圳 新旧程度： |
|||||
| 联系人：陈小姐 |
| 电 话：0755-83605789 |
| 手 机：13428979109 |
| QQ：656259901,307704921 |
| MSN：chenqiongxia18@126.com |
| 传 真：0755-23816523 |
| EMail：656259901@qq.com |
| 公司地址： 广东深圳市福田区华强北（振华路）赛格高科德电子市场A1848室 |
